Driving this Canter FG was like seeing an old friend who’s aged gracefully.
It’d been at least 10 years since I drove and wrote about an earlier version of Mitsubishi Fuso’s unique-to-North America cab-over-engine 4×4. Now updated with a refined Canter cab and other advances, the recently introduced model was even better.
The FG is unique because all other 4x4s on this continent, whether from Ford, General Motors, Chrysler, Nissan or Toyota, are the conventional-cab style with a protruding nose that houses the engine. Most buyers prefer that style. The domestic Big Three all make trucks as heavy as the Fuso FG, but only the FG’s a cabover. This matters to buyers who like a cabover’s compactness and maneuverability.
Sometimes called low-cab-forward or tiltcab, this truck type is ubiquitous almost everywhere else in the world. Commercial-vehicle length limits overseas make the cabover all but mandatory, and even mini-trucks use the design. Fuso and others build cabovers for most of the world’s markets, so they sell them here, too, though not in big numbers.
Early last year, Mitsubishi Fuso Truck of America began importing the Canters, which also have 2010-legal diesels and automated-mechanical transmissions as standard equipment. The parent company in Japan is 89% owned by Daimler Trucks of Germany, making Fuso a cousin to Freightliner and Western Star. Fuso’s 4P10 four-cylinder diesel uses a Daimler-style BlueTec urea-injection system. The 3-liter engine’s horsepower and torque numbers are modest – 161 and 295, respectively – but it scoots anyway, and the truck is fun to drive.
The dual-clutch AMT is called Duonic. It shifts quickly, smoothly and without the low-speed slippage inherent in torque converter-type automatics used by competitors. It replaces a five-speed manual tranny used on earlier FGs, making the truck easy to drive for the experienced and novice alike. The FG’s single-speed transfer case is operated by a rocker switch on the dashboard, and manually locking hubs – not a very modern feature, I thought – engage the front wheels for off-road movement. Unlocking the TC and hubs enhances fuel economy during travel on pavement and graded trails.
For a given body length, a cabover’s wheelbase and overall length are several feet shorter than a conventional’s. This makes it easy to slip through urban traffic and scoot around job sites, and usually means outward visibility for its driver is better. This is a real plus off-road: When cresting a hill, you can see what’s immediately ahead and below from behind the wheel of a cabover, but all you see with a conventional is its hood.
Off-road hill climbing – that’s what we needed to do. So Tom Hotham, Fuso’s representative in Ohio, arranged an excursion at a large quarry in a distant corner of the state. It’s got trails and hills for us to drive over, he said, so off we went, only to find out that this FG’s rib-type tires – optional fitment if a truck will spend a lot of time on pavement – slipped in the sandy soil at the quarry, and we were sadly confined to harder surfaces. Any FG destined for frequent off-road use ought to get block-treaded “traction” tires, and they are available.
However, the FG’s high stance, at least a foot more than two-wheel-drive Canters, allowed it to shrug off obstacles on more solid terrain. The cab is also higher, which makes climbing in more of a chore, and I was pretty clumsy at first. But big grab handles on the A-pillars help driver and passenger pull themselves in (not that the younger and more agile Hotham needed much help). There’s room for three people in the wide cab, and the center seat back folds down to make a work surface for a laptop or paperwork.
This FG was set up by Churney’s Truck Center, a Fuso, Hino and UD dealer near Cleveland, Ohio, just for my test drive. The shop temporarily mounted a flatbed body, which carried about 1,000 pounds of borrowed building materials that we hauled to and from the quarry about 70 miles east of the city. The property, south of Thompson in northeastern Ohio, is owned by the Sidley Company, which has a division that sells Fuso and Mack trucks. People there showed us around the huge premises, now bustling with quarrying and filtering of sand to support natural gas drilling in the region.
Those rib-treaded tires proved quiet and comfortable on a high-speed run along Interstate 80, during which the FG’s four-cylinder diesel busily spun at about 2,900 rpm at 70 mph. This was a function of the numerically high rear-end ratio and put the needle several hundred rpm outside the green zone arrayed on the tachometer, but still in its operating range so the engine didn’t complain.
It also revved enthusiastically as the Duonic tranny went through its six ratios. Shouldn’t it upshift sooner? I complained to Hotham, who was in the shotgun seat. He reached over and punched a rocker switch on the dash. This changed the tranny from Performance to Economy, and it then upshifted at lower revs, keeping the tach needle in that 1,500-to-2,500 green zone.
The Duonic seemed to know exactly what it was doing, always choosing a good gear for every situation. It can be controlled by slapping the selector to the left as it’s in D, then up to make an upshift or down for a downshift. Usually it’s better to leave it in D.
A few weeks later I went on a Fuso-sponsored trip to Japan, and drove another FG at the company’s test facility. Here the tranny stumbled while assaulting a 12% paved upgrade. I had chosen Economy mode, and the Duonic got confused; it downshifted, then unwisely upshifted and the engine began bogging down and seemed about to stall. But I punched in Performance and it immediately recovered, downshifting again to let the engine rev and make some power. So Performance is the setting to use under demanding conditions.
The FG rode smoothly on well-maintained interstate pavement, but because it’s a serious Class 4 truck with a stiff suspension, it bounced actively as we barreled over broken concrete on Cleveland-area streets.
A low cabover might look small in photos, but approach one and you’ll see that it’s really a sizeable thing. The tall FG is even more so. With a gross weight rating of 14,080 pounds, more than half of which is payload, it’s not a light truck, either. Its primary competitor in North America is Ford’s F-450 4×4, which sits low by comparison. The FG also has a larger price, but Mitsubishi Fuso claims it’ll deliver a lower total cost of ownership. That includes low depreciation: Look for a 10-year-old FG and see what its seller is asking for it; you might be surprised.
Ease of maintenance is another cabover advantage. Most conventional-cab trucks in this weight class have automobile-like alligator hoods that open to reveal hoses, wiring and shrouding that hide the engine. Getting at it often requires removing something, then leaning over the radiator or fenders to reach what needs attention.
But the cab of a Fuso Canter tilts forward on front hinges – just snap loose a rear lock, grasp the cab’s bottom and lift it, and up it goes, rather easily. Now you’ve completely bared the engine and all its accessories. Then you just step up to it and do what you must in the way of maintenance or repairs. Fluid checks can be done without even tilting the hood.
Aided by a pickup-like wheelbase of 134.4 inches, an FG’s turning diameter measures 44.2 feet, which is 7 feet smaller than an F-450’s, Fuso says. Yet there’s enough room on the frame for a body that’s 12 to 15 feet long. In fact, while going in circles with a low cabover such as this FG, I almost feel I could run into the body behind me.
Truck: Fuso FG 4×4, low cab-over-engine, GVW 14,050 lbs., payload (w/ body) 8,130 lbs., cab-to-axle area 104.8 in.
Engine: Fuso 4P10, inline 4-cylinder turbodiesel, EPA 2010-legal w/BlueTec urea injection, 3 liters (183 cu in), 161 hp @ 3,500 rpm, 295 lb-ft @ 1,600 rpm
Transmission: Mitsubishi Fuso Duonic dual-clutch automated mechanical, 6-speed overdrive
Axles: Proprietary, 6,175 lbs. front, 9,480 lbs. rear, w/5.285 ratio, on laminated leaf springs
Wheelbase: 134.2 in.
Tires wheels: 235/85R16 highway or traction type, on steel discs
Brakes: Vacuum-assisted drums
Steering: Integrated hydraulic power w/tilt and telescoping column
Fuel tank: 33 gal. steel
Body: Churney’s steel flatbed (temporary)
From the February 2012 issue of HDT.
Light Medium: Related News
2/28/2012 – Test Drive: Fuso FG 4×4 Goes Almost Anywhere
Driving this Canter FG was like seeing an old friend who’s aged gracefully….
1/24/2012 – Test Drive: Ram Tradesman is Quiet, Comfortable, Fast — But Built for Work
I recently sold my ’87 Dodge W150 pickup, and I don’t miss it at all.
Oh, I liked it when I bought it a year earlier, because it was a funky Power Ram 4×4,…